Sign in

username:

password:



Not a member?

Search Comp.Arch.FPGA



Search tips

fpga by Keywords

Altera | ASIC | CPLD | Cyclone | DCM | DDR | DSP | Ethernet | ISE | JTAG | Linux | LVDS | Microblaze | ML310 | Modelsim | NIOS | OPB | PCI | Quartus | RocketIO | SDRAM | Spartan | Spartan3 | SRAM | Stratix | Verilog | VHDL | Virtex | Virtex-4 | Virtex-II | Xilinx | XST


Ads

See Also

DSPEmbedded SystemsElectronics

Comp.Arch.FPGA | FPGA configuration mode on ML310

There are 5 messages in this thread.

You are currently looking at messages 0 to 5.

FPGA configuration mode on ML310 - grant0920 - 2008-04-07 10:17:00

Hi! everyone

I have a very basic problem. I know that the 6-position DIP switch on
the ML403 board can control the configuration address and FPGA
configuration mode. On the ML310 board, I am not sure where can set
the FPGA configuration mode. I want to set the configuration mode of
my ML310 borad as the SelectMAP mode. Please tell me how to set its
FPGA configuration mode. Thanks very much!



Re: FPGA configuration mode on ML310 - Antti - 2008-04-07 10:51:00

On 7 Apr., 16:17, grant0920
<grant0...@gmail.com> wrote:
> Hi! everyone
>
> I have a very basic problem. I know that the 6-position DIP switch on
> the ML403 board can control the configuration address and FPGA
> configuration mode. On the ML310 board, I am not sure where can set
> the FPGA configuration mode. I want to set the configuration mode of
> my ML310 borad as the SelectMAP mode. Please tell me how to set its
> FPGA configuration mode. Thanks very much!

try reading the manuals!

Antti

Re: FPGA configuration mode on ML310 - grant0920 - 2008-04-07 11:08:00

On 4$B7n(B7$BF|(B,
$B2<8a(B10$B;~(B51$BJ,(B, Antti <Antti.Luk...@googlemail.com> wrote:
> On 7 Apr., 16:17, grant0920 <grant0...@gmail.com> wrote:
>
> > Hi! everyone
>
> > I have a very basic problem. I know that the 6-position DIP switch on
> > the ML403 board can control the configuration address and FPGA
> > configuration mode. On the ML310 board, I am not sure where can set
> > the FPGA configuration mode. I want to set the configuration mode of
> > my ML310 borad as the SelectMAP mode. Please tell me how to set its
> > FPGA configuration mode. Thanks very much!
>
> try reading the manuals!
>
> Antti

Hi! Antti

I have read the manuals. I think the configuration mode can be setted
by using the SYSACE CFG SW3. But the result doesn't seem to my
expectancy so that I want check if the setting is correct. Is my
setting right?
______________________________
Join the blogging team on FPGARelated.com and earn rewards! Details Here.

Re: FPGA configuration mode on ML310 - Ed McGettigan - 2008-04-07 21:32:00

grant0920 wrote:
> Hi! everyone
> 
> I have a very basic problem. I know that the 6-position DIP switch on
> the ML403 board can control the configuration address and FPGA
> configuration mode. On the ML310 board, I am not sure where can set
> the FPGA configuration mode. I want to set the configuration mode of
> my ML310 borad as the SelectMAP mode. Please tell me how to set its
> FPGA configuration mode. Thanks very much!

This can't be done.  There is no support for SelectMAP configuration
on the ML310.

Ed McGettigan
--
Xilinx Inc.
______________________________
Join the blogging team on FPGARelated.com and earn rewards! Details Here.

Re: FPGA configuration mode on ML310 - grant0920 - 2008-04-08 22:07:00

On 4$B7n(B8$BF|(B,
$B>e8a(B9$B;~(B32$BJ,(B, Ed McGettigan <ed.mcgetti...@xilinx.com> wrote:
> grant0920 wrote:
> > Hi! everyone
>
> > I have a very basic problem. I know that the 6-position DIP switch on
> > the ML403 board can control the configuration address and FPGA
> > configuration mode. On the ML310 board, I am not sure where can set
> > the FPGA configuration mode. I want to set the configuration mode of
> > my ML310 borad as the SelectMAP mode. Please tell me how to set its
> > FPGA configuration mode. Thanks very much!
>
> This can't be done.  There is no support for SelectMAP configuration
> on the ML310.
>
> Ed McGettigan
> --
> Xilinx Inc.

Thanks very much for your kindly reply.
So, where can I chage the configuration mode on the ML310 if I want to
use the ICAP to configure my design?
I want to change my configuration mode except for the boundary scan
mode. Thanks!
______________________________
Join the blogging team on FPGARelated.com and earn rewards! Details Here.