On Feb 4, 8:11 pm, "Dwayne Dilbeck" <ddilb...@yahoo.com> wrote:
> Same here.. It is working fine for me too. You might want to remove the
> instalation and re-install the software.*CRINGE*
>
> "Arlet Ottens" <usene...@c-scape.nl> wrote in message
>
> news:47a5a30e$0$85789$e4fe514c@news.xs4all.nl...
>
> > pallavi wrote:
> >> Hello,
> >> I want to set up design environment for my new Spartan-3E FPGA starter
> >> kit.
> >> I have downloaded ISE WebPack 9.2 and the service pack 9.2i SP4.
> >> To my dismay, when I want to point to my target device at the start or
> >> later(Set Properties for project), the Family drop-down, doesnot show
> >> of all the things, Spartan-3E.
>
> > I don't know what's wrong with your setup, but I'm using ISE WebPack
> > 9.2.04i, and it shows the Spartan-3E devices.
Yes, i had to remove and reinstall and it worked. It was probably the
sleepy web install overnight, at the first instance.
Reply by Dwayne Dilbeck●February 4, 20082008-02-04
Same here.. It is working fine for me too. You might want to remove the
instalation and re-install the software.*CRINGE*
"Arlet Ottens" <usenet+5@c-scape.nl> wrote in message
news:47a5a30e$0$85789$e4fe514c@news.xs4all.nl...
> pallavi wrote:
>> Hello,
>> I want to set up design environment for my new Spartan-3E FPGA starter
>> kit.
>> I have downloaded ISE WebPack 9.2 and the service pack 9.2i SP4.
>> To my dismay, when I want to point to my target device at the start or
>> later(Set Properties for project), the Family drop-down, doesnot show
>> of all the things, Spartan-3E.
>>
>
> I don't know what's wrong with your setup, but I'm using ISE WebPack
> 9.2.04i, and it shows the Spartan-3E devices.
Reply by Arlet Ottens●February 3, 20082008-02-03
pallavi wrote:
> Hello,
> I want to set up design environment for my new Spartan-3E FPGA starter
> kit.
> I have downloaded ISE WebPack 9.2 and the service pack 9.2i SP4.
> To my dismay, when I want to point to my target device at the start or
> later(Set Properties for project), the Family drop-down, doesnot show
> of all the things, Spartan-3E.
>
I don't know what's wrong with your setup, but I'm using ISE WebPack
9.2.04i, and it shows the Spartan-3E devices.
Reply by pallavi●February 3, 20082008-02-03
Hello,
I want to set up design environment for my new Spartan-3E FPGA starter
kit.
I have downloaded ISE WebPack 9.2 and the service pack 9.2i SP4.
To my dismay, when I want to point to my target device at the start or
later(Set Properties for project), the Family drop-down, doesnot show
of all the things, Spartan-3E.
These options are available: Some Coolrunners, some CPLD's, Spartan 3A
DSP and Spartan 3A and 3AN.
I tried with Spartan-3A DSP and FPGA, but after bitstream generation,
when I want to flash the design, there is some error, which is
obviously because of wrong target device.
Did I do something wrong. Can anyone, please lead me to a good 'how
to' about this problem and also to start and set up my environment.
Where can I get it to point it to synthesise for Spartan-3E? Do I
have to use a previous version like 8.2 from the DVD, that came with
the kit?
It took a whole night to install Webpack 9.2 from internet. And I
suppose ISE 9.2 supports 3E, atleast it mentions that it supports,
but where?
Please enlighten me.
Thanks.
Pallavi