On 4$B7n(B8$BF|(B, $B>e8a(B9$B;~(B32$BJ,(B, Ed McGettigan <ed.mcgetti...@xilinx.com> wrote:
> grant0920 wrote:
> > Hi! everyone
>
> > I have a very basic problem. I know that the 6-position DIP switch on
> > the ML403 board can control the configuration address and FPGA
> > configuration mode. On the ML310 board, I am not sure where can set
> > the FPGA configuration mode. I want to set the configuration mode of
> > my ML310 borad as the SelectMAP mode. Please tell me how to set its
> > FPGA configuration mode. Thanks very much!
>
> This can't be done. There is no support for SelectMAP configuration
> on the ML310.
>
> Ed McGettigan
> --
> Xilinx Inc.
Thanks very much for your kindly reply.
So, where can I chage the configuration mode on the ML310 if I want to
use the ICAP to configure my design?
I want to change my configuration mode except for the boundary scan
mode. Thanks!
Reply by Ed McGettigan●April 7, 20082008-04-07
grant0920 wrote:
> Hi! everyone
>
> I have a very basic problem. I know that the 6-position DIP switch on
> the ML403 board can control the configuration address and FPGA
> configuration mode. On the ML310 board, I am not sure where can set
> the FPGA configuration mode. I want to set the configuration mode of
> my ML310 borad as the SelectMAP mode. Please tell me how to set its
> FPGA configuration mode. Thanks very much!
This can't be done. There is no support for SelectMAP configuration
on the ML310.
Ed McGettigan
--
Xilinx Inc.
Reply by grant0920●April 7, 20082008-04-07
On 4$B7n(B7$BF|(B, $B2<8a(B10$B;~(B51$BJ,(B, Antti <Antti.Luk...@googlemail.com> wrote:
> On 7 Apr., 16:17, grant0920 <grant0...@gmail.com> wrote:
>
> > Hi! everyone
>
> > I have a very basic problem. I know that the 6-position DIP switch on
> > the ML403 board can control the configuration address and FPGA
> > configuration mode. On the ML310 board, I am not sure where can set
> > the FPGA configuration mode. I want to set the configuration mode of
> > my ML310 borad as the SelectMAP mode. Please tell me how to set its
> > FPGA configuration mode. Thanks very much!
>
> try reading the manuals!
>
> Antti
Hi! Antti
I have read the manuals. I think the configuration mode can be setted
by using the SYSACE CFG SW3. But the result doesn't seem to my
expectancy so that I want check if the setting is correct. Is my
setting right?
Reply by Antti●April 7, 20082008-04-07
On 7 Apr., 16:17, grant0920 <grant0...@gmail.com> wrote:
> Hi! everyone
>
> I have a very basic problem. I know that the 6-position DIP switch on
> the ML403 board can control the configuration address and FPGA
> configuration mode. On the ML310 board, I am not sure where can set
> the FPGA configuration mode. I want to set the configuration mode of
> my ML310 borad as the SelectMAP mode. Please tell me how to set its
> FPGA configuration mode. Thanks very much!
try reading the manuals!
Antti
Reply by grant0920●April 7, 20082008-04-07
Hi! everyone
I have a very basic problem. I know that the 6-position DIP switch on
the ML403 board can control the configuration address and FPGA
configuration mode. On the ML310 board, I am not sure where can set
the FPGA configuration mode. I want to set the configuration mode of
my ML310 borad as the SelectMAP mode. Please tell me how to set its
FPGA configuration mode. Thanks very much!