The problem releated to the memory is solved after I installed ISE 9.2
sp4 and EDK 9.2 sp2.



On Dec 1, 10:56=A0pm, SUMAN <suman...@gmail.com> wrote:
> No , I have not. I am planning to install them.

No , I have not. I am planning to install them.

The 1800A board's DDR2 was tested extensively by both Avnet and Xilinx
in ISE/EDK 9.2.

Xilinx is running Linux from the DDR2 in example design
http://www.xilinx.com/support/documentation/boards_and_kits/ug486.pdf.
This design is currently at 10.1, but I believe it was originally
posted for ISE/EDK 9.2.

You can also go to the Avnet Design Resource Center for some extra
designs for this board:  www.em.avnet.com/spartan3a-dsp.  Click on
Support Files & Downloads.  Both MIG and MicroBlaze designs that use
the DDR2 are posted for ISE/EDK 9.2.  For MicroBlaze, the S3A1800DSP
BPI Flash Configuration and Bootloading design specifically has a DDR2
memory test.

Regarding your issues, SUMAN, have you installed the service packs for
both ISE and EDK?

Bryan


On Nov 30, 8:33=A0pm, bish <bishes...@gmail.com> wrote:
> On Nov 30, 11:28=A0pm, SUMAN <suman...@gmail.com> wrote:> Hi,
> > =A0I am student using spartan 3a dsp 1800 board with EDK/ise 9.2i . In
> > EDK I had used BSB to create new project using default configuration
> > for the following peripherals:-
> > 1) microblaze (with bram 64KB) ,clock
> > 2)RST32_UART
> > 3)LED ,PUSH, DIP.
> > 4)DDR2 SDRAM using MPMC peripheral
>
> > I had used all default settings to the end of bsb.
>
> > When i downloaded bitseam in the board , i got MEMORY TEST FAILURE
> > (for 32 ,16 and 8 bit) message in hyperterminal .
>
> I doubt that xilinx and avnet people ever tested the spartan 3a dsp
> 1800a board with edk 9.2i. As they provide the edk 9.2i with this
> board they shoud have tested the board building reference systems WITH
> EDK 9.2i. It seems they didn't do that and people like us get a lot of
> trouble and lot of time wasted unnecessarily!!
>
>
>
> > But other peripherals are working fine.
> > I can't understand what the problem is. Does any body has solution?- Hi=
de quoted text -
>
> - Show quoted text -

On Nov 30, 11:28=A0pm, SUMAN <suman...@gmail.com> wrote:
> Hi,
> =A0I am student using spartan 3a dsp 1800 board with EDK/ise 9.2i . In
> EDK I had used BSB to create new project using default configuration
> for the following peripherals:-
> 1) microblaze (with bram 64KB) ,clock
> 2)RST32_UART
> 3)LED ,PUSH, DIP.
> 4)DDR2 SDRAM using MPMC peripheral
>
> I had used all default settings to the end of bsb.
>
> When i downloaded bitseam in the board , i got MEMORY TEST FAILURE
> (for 32 ,16 and 8 bit) message in hyperterminal .
>
I doubt that xilinx and avnet people ever tested the spartan 3a dsp
1800a board with edk 9.2i. As they provide the edk 9.2i with this
board they shoud have tested the board building reference systems WITH
EDK 9.2i. It seems they didn't do that and people like us get a lot of
trouble and lot of time wasted unnecessarily!!

> But other peripherals are working fine.
> I can't understand what the problem is. Does any body has solution?

Hi,
 I am student using spartan 3a dsp 1800 board with EDK/ise 9.2i . In
EDK I had used BSB to create new project using default configuration
for the following peripherals:-
1) microblaze (with bram 64KB) ,clock
2)RST32_UART
3)LED ,PUSH, DIP.
4)DDR2 SDRAM using MPMC peripheral

I had used all default settings to the end of bsb.

When i downloaded bitseam in the board , i got MEMORY TEST FAILURE
(for 32 ,16 and 8 bit) message in hyperterminal .

But other peripherals are working fine.
I can't understand what the problem is. Does any body has solution?