Forums Search for: Spartan3
Spartan 3E slower that Spartan 3?
inHello guys, I just made a quick speed test in ISE 7.1 with a Spartan 3E device. A 32-bit counter runs at 129 MHz in XC3S500E-4, but in a Spartan...
Hello guys, I just made a quick speed test in ISE 7.1 with a Spartan 3E device. A 32-bit counter runs at 129 MHz in XC3S500E-4, but in a Spartan 3 XC3S400-4 at a higher 168 MHz. Also checked a few other desings, like DDR SDRAM controller, and they all run about 20% slower on Spartan 3Es. I don't get it, isn't 3E series supposed to have the same core as the Spartan 3? Best Regards George ...
Spartan 2 & 3, serial config and CS pin
inSpartan 2 docs clearly says that, even though you are configuring the FPGA in serial mode, you should keep CS pin high. What about Spartan...
Spartan 2 docs clearly says that, even though you are configuring the FPGA in serial mode, you should keep CS pin high. What about Spartan 3? I don't see something like: "Yes, Spartan 2 had an error, but it has been fixed in Spartan 3"
Spartan-3 -> Spartan-2 problem
About two months ago I've started learning VHDL, CPLD and FPGA. Right from the start I've choosen Spartan-3 (XC3S50) and didn't look at...
About two months ago I've started learning VHDL, CPLD and FPGA. Right from the start I've choosen Spartan-3 (XC3S50) and didn't look at Spartan-II because I wanted to use the latest chip. Now I am making a board with 50 5V TTL inputs and idea was to use the CPLD XC95144XL as a level translator...but I just don't like it. So, now I am trying Spartan-II (XC2S50), which is 5V tolerant, an...
Spartan-3 : preconfiguration pull-up/float ?
inHi, For the Spartan-II, the preconfiguration pullup resistors were selected by the M2 configuration pin. What about for the Spartan-3? My...
Hi, For the Spartan-II, the preconfiguration pullup resistors were selected by the M2 configuration pin. What about for the Spartan-3? My new design has to connect an ARM7TDMI bus to the SPARTAN-3. I need to make sure my ucLinux will boot correctly, and so make sure about the IO pins states of the SPARTAN-3 on the poweron. Regards, Laurent
Xilinx Spartan E
inWhat happend to the Spartan E? Is it eaten up by the Spartan 3A and 3AN? The Spartan 3A starter kit from Xilinx looks like it's from...
What happend to the Spartan E? Is it eaten up by the Spartan 3A and 3AN? The Spartan 3A starter kit from Xilinx looks like it's from Digilent. But the Digilent web site didn't show the Spartan 3A development kit. Brad Smallridge Ai Vision
Config Spartan3 in serial slave mode
inHi, I have a design where a Spartan XL was replaced by a Spartan 3. The FPGA is configured by an ATmega MCU which loads the configuration...
Hi, I have a design where a Spartan XL was replaced by a Spartan 3. The FPGA is configured by an ATmega MCU which loads the configuration file into the FPGA. This procedure works fine with the old board and the Spartan XL, but with the Spartan 3 I have the trouble that I never get the DONE signal, after the configuration is done. I see data going over the DIN line into the Spartan 3 ...
Which WebPack for old Spartan and Spartan-2?
inI'm looking for a good stable version of WebPack that supports the old Spartan and Spartan-2 devices for legacy product maintenance. Any...
I'm looking for a good stable version of WebPack that supports the old Spartan and Spartan-2 devices for legacy product maintenance. Any recommendations? Regards; Leland C. Scott KC8LDO
Which WebPack for old Spartan and Spartan-2?
I'm looking for a good stable version of WebPack that supports the old Spartan and Spartan-2 devices for legacy product maintenance....
I'm looking for a good stable version of WebPack that supports the old Spartan and Spartan-2 devices for legacy product maintenance. Any recommendations? Regards; Leland C. Scott KC8LDO
Which WebPack for old Spartan and Spartan-2?
I'm looking for a good stable version of WebPack that supports the old, Spartan and Spartan-2 devices for legacy product maintenance....
I'm looking for a good stable version of WebPack that supports the old, Spartan and Spartan-2 devices for legacy product maintenance. Any recommendations? Regards; Leland C. Scott KC8LDO
Xilinx Spartan II and 5V PCI
inHello all, I am using a Xilinx Spartan II FPGA on a prototype PCI add-in card as the PCI device attached to the bus. According to the Spartan...
Hello all, I am using a Xilinx Spartan II FPGA on a prototype PCI add-in card as the PCI device attached to the bus. According to the Spartan II data sheet it appears that 5V PCI compatible IOs are indeed instantiable which was the very reason for going with a Spartan II in the first place. However, after correlating the appropriate requirements from the PCI spec with what is claimed in...
Spartan XL Tool Support
inHello I want to use Spartan XL FPGA for a project and found out that my installation of the Xilinx ISE 5.2 i (Alliance) does not support...
Hello I want to use Spartan XL FPGA for a project and found out that my installation of the Xilinx ISE 5.2 i (Alliance) does not support this device. I can only install later versions of the Spartan devices and not the XL family. Can I get some suggestions on what I should do to use Spartan XL? I dont want to go to the WebPack Option. Thanks Anup
classic Spartan-3 DDR2 and IOBs
inHello! I'm a bit ambitious (crazy?) and trying to get a Spartan-3 design talking to a set of DDR2 ICs. I'm exploring my termination options, and...
Hello! I'm a bit ambitious (crazy?) and trying to get a Spartan-3 design talking to a set of DDR2 ICs. I'm exploring my termination options, and I've seen the following: 1. The Spartan-3AN Starter kit terminates all of the DDR2 signals by pulling them to 0.9V through a 50-ohm resistor. The Spartan-3{A, AN, E} series lack DCI on their IOBs. 2. The Spartan-3 (classic) datasheet shows that...
Migration from Spartan-2E to Spartan-3E
inHi, I'm investigating the possibility to replace an Spartan-2E (xc2s400e) with an Spartan-3E (xc3s1200e) device on a PCB. The core voltage...
Hi, I'm investigating the possibility to replace an Spartan-2E (xc2s400e) with an Spartan-3E (xc3s1200e) device on a PCB. The core voltage drops from 1.8V to 1.2V. Has anyone experience regarding the footprint differences (easy/hard/impossible to adapt) and any other differences which must be taken into account? Regards, Stefan
Spartan: How to select device as Spartan/SpartanXL
I need to use spartan series FPGA for a design.( As design have only 5 V supply available). when I start a new project in XILINX ISE 6.1 I dont...
I need to use spartan series FPGA for a design.( As design have only 5 V supply available). when I start a new project in XILINX ISE 6.1 I dont get option of Spartan in Device selection list. can anyone help me out. which software do I need. Thanks for any help
design in vsprom
I have a design for vsprom.My idea is that config FPGA with Xilinx CPLD and parallel flash memory.The design is correct in spartan platform...
I have a design for vsprom.My idea is that config FPGA with Xilinx CPLD and parallel flash memory.The design is correct in spartan platform but failure in spartan-2.Can u give me some suggestions? I know that the algorithm of config spartan and sparan-2 is different.There is a internal counter for spartan bitstream,but the spartan-2 use command reg for the bitstream control.Is this the reas...
Spartan 3E and Spartan 3 with GTL
Hello I'm wondering what alternatives I have to GTL on an Spartan 3E. I would like to use an output pin as an open collector output with...
Hello I'm wondering what alternatives I have to GTL on an Spartan 3E. I would like to use an output pin as an open collector output with an external pull-up to 5 Volt. This is to interface 5 Volt logic. On the Spartan 3 we used GTL outputs.
Spartan-4 ?
inNew low cost families other than from Xilinx are known to be coming this autumn (Cyclone-3, MAX3, LatticeXP2) but there is no advance info an...
New low cost families other than from Xilinx are known to be coming this autumn (Cyclone-3, MAX3, LatticeXP2) but there is no advance info an Spartan-4 yet, is there a hope at all that there will be modern low cost family from Xilinx too? Spartan-3 is 'not for new designs' as there is no price roadmap for it, Spartan-3E only has small members, eg not replacement for S3 so we have vacuum ...
SPROM for Spartan II
inHello, all, I am working on an update for a board that now uses an original 5-V Spartan (XCS30) part. To reduce cost, I'm looking at using...
Hello, all, I am working on an update for a board that now uses an original 5-V Spartan (XCS30) part. To reduce cost, I'm looking at using the Spartan II XC2S30 part, which is less than half the price. (I'd go with the Spartan IIE, but the smallest is 50K gates, and config bitstream is about double the 2S30's requirement, which negates the price advantage.) Anyway, there are some 512...
DDR2 @ 400 MHz and Xilinx Spartan-3A[N] kits
inXilinx has three very similar kits: - Spartan-3A Starter Kit, - Spartan-3AN Starter Kit, and - Spartan-3A DDR2 SDRAM Interface Development...
Xilinx has three very similar kits: - Spartan-3A Starter Kit, - Spartan-3AN Starter Kit, and - Spartan-3A DDR2 SDRAM Interface Development Kit. Only the latter is promoted as supporting DDR2 @ 400 MHz, but the only difference listed between it and the Spartan-3A Starter Kit is the 133 MHz Crystal Oscillator and the lack of a 16 character, 2-Line LCD display. Is there some special about...
Spartan-6
init seems that first references to the upcoming Spartan family are in the wild already http://www.linkedin.com/in/ericschristiansen I assume...
it seems that first references to the upcoming Spartan family are in the wild already http://www.linkedin.com/in/ericschristiansen I assume the spartan-6 mentioned there is not a typo (actually i am almost sure it isnt) Antti