I am having about the same experience. I upgraded my computer to EDK/ISE 8.2 1. I upgraded my GSRD2 (PPC, MPMC2, TEMAC) design to v8.2. There were actually no problems detected until I used the flashwriter.tcl script. I does not work at all. OK, minor thing to remedy. 2. I upgraded my PPC CoreConnect project to 8.2. First the XMD connect failure (wrong processor version 0x00000000). Then I connected secesfully using "connect ppc hw", but the design does not work at all - probably some hw error. The sw crashes when setting interrupt controller (working nice in 8.1). Fu.. that 8.2 and hope for the SP2 to remedy the problems. Cheers, Guru Zara wrote:> On 27 Oct 2006 00:18:43 -0700, "Antti" <Antti.Lukats@xilant.com> > wrote: > > >Zara schrieb: > > > >> I quit. > >> > >> A brand new project, with only a dcm, a debug module, 16K ram, an uart > >> and intc will not work (problems writing BRAM). > >> > >> Will continue using 8.1 for a long time, I suspect > > > >quit? your life? > > > >EDK 8.2 does work > >I have done maybe over 50 EDK systems with 8.2 > >- all of them work > > > >if your system doesnt there is something wrong > >and you should figure out what it is, not quitting. > > > >Antti > > > No, it was a figure of speech. Whta I really mean is that I will stop > investigation while I am completing the current phase of my project. > As soon as some 40something boarsd are delivered; I will resume > trying. > > As a sapnish adage goes "Last to be lost is Hope" ;-) > > Regards, > > Zara
Problema when upgrading from Xilinx 8.1 to Xilinx 8.2
Started by ●October 19, 2006
Reply by ●October 29, 20062006-10-29
Reply by ●October 30, 20062006-10-30
On 29 Oct 2006 09:43:10 -0800, "Guru" <ales.gorkic@email.si> wrote:>I am having about the same experience. >I upgraded my computer to EDK/ISE 8.2 > >1. I upgraded my GSRD2 (PPC, MPMC2, TEMAC) design to v8.2. There were >actually no problems detected until I used the flashwriter.tcl script. >I does not work at all. OK, minor thing to remedy. > >2. I upgraded my PPC CoreConnect project to 8.2. First the XMD connect >failure (wrong processor version 0x00000000). Then I connected >secesfully using "connect ppc hw", but the design does not work at all >- probably some hw error. The sw crashes when setting interrupt >controller (working nice in 8.1). > >Fu.. that 8.2 and hope for the SP2 to remedy the problems. > >Cheers, > >GuruI am jus wondering if ther problem lies: 1. Either in the target selected (some problem with Syn/Xlat/Map/Par): I am using an Spartan 3: 3S400 2. Or in the Computer: I am using an AthlonX2, both in the dual 8.1/8.2 installation, and in a clean 8.2 installation on a bran new laptop, that also fails. Antti? Guru? Do you see any recurrence here? Zara
Reply by ●November 1, 20062006-11-01
Using Virtex4FX12, laptop P4M 1.7GHz and ISE 8.1 SP3 and EDK 8.2 SP1. Strange, because I rebuld one MB project in 8.2 for S3ESK and it worked fine. I think this are some bugs that emerge from time to time. Lets pray that EDK SP2 will solve the problem. Cheers, Guru Zara wrote:> On 29 Oct 2006 09:43:10 -0800, "Guru" <ales.gorkic@email.si> wrote: > > >I am having about the same experience. > >I upgraded my computer to EDK/ISE 8.2 > > > >1. I upgraded my GSRD2 (PPC, MPMC2, TEMAC) design to v8.2. There were > >actually no problems detected until I used the flashwriter.tcl script. > >I does not work at all. OK, minor thing to remedy. > > > >2. I upgraded my PPC CoreConnect project to 8.2. First the XMD connect > >failure (wrong processor version 0x00000000). Then I connected > >secesfully using "connect ppc hw", but the design does not work at all > >- probably some hw error. The sw crashes when setting interrupt > >controller (working nice in 8.1). > > > >Fu.. that 8.2 and hope for the SP2 to remedy the problems. > > > >Cheers, > > > >Guru > > I am jus wondering if ther problem lies: > 1. Either in the target selected (some problem with Syn/Xlat/Map/Par): > I am using an Spartan 3: 3S400 > 2. Or in the Computer: I am using an AthlonX2, both in the dual > 8.1/8.2 installation, and in a clean 8.2 installation on a bran new > laptop, that also fails. > > Antti? Guru? Do you see any recurrence here? > > Zara